jidctflt.c 8.14 KB
Newer Older
wester committed
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235
/*
 * jidctflt.c
 *
 * Copyright (C) 1994-1998, Thomas G. Lane.
 * Modified 2010 by Guido Vollbeding.
 * This file is part of the Independent JPEG Group's software.
 * For conditions of distribution and use, see the accompanying README file.
 *
 * This file contains a floating-point implementation of the
 * inverse DCT (Discrete Cosine Transform).  In the IJG code, this routine
 * must also perform dequantization of the input coefficients.
 *
 * This implementation should be more accurate than either of the integer
 * IDCT implementations.  However, it may not give the same results on all
 * machines because of differences in roundoff behavior.  Speed will depend
 * on the hardware's floating point capacity.
 *
 * A 2-D IDCT can be done by 1-D IDCT on each column followed by 1-D IDCT
 * on each row (or vice versa, but it's more convenient to emit a row at
 * a time).  Direct algorithms are also available, but they are much more
 * complex and seem not to be any faster when reduced to code.
 *
 * This implementation is based on Arai, Agui, and Nakajima's algorithm for
 * scaled DCT.  Their original paper (Trans. IEICE E-71(11):1095) is in
 * Japanese, but the algorithm is described in the Pennebaker & Mitchell
 * JPEG textbook (see REFERENCES section in file README).  The following code
 * is based directly on figure 4-8 in P&M.
 * While an 8-point DCT cannot be done in less than 11 multiplies, it is
 * possible to arrange the computation so that many of the multiplies are
 * simple scalings of the final outputs.  These multiplies can then be
 * folded into the multiplications or divisions by the JPEG quantization
 * table entries.  The AA&N method leaves only 5 multiplies and 29 adds
 * to be done in the DCT itself.
 * The primary disadvantage of this method is that with a fixed-point
 * implementation, accuracy is lost due to imprecise representation of the
 * scaled quantization values.  However, that problem does not arise if
 * we use floating point arithmetic.
 */

#define JPEG_INTERNALS
#include "jinclude.h"
#include "jpeglib.h"
#include "jdct.h"		/* Private declarations for DCT subsystem */

#ifdef DCT_FLOAT_SUPPORTED


/*
 * This module is specialized to the case DCTSIZE = 8.
 */

#if DCTSIZE != 8
  Sorry, this code only copes with 8x8 DCTs. /* deliberate syntax err */
#endif


/* Dequantize a coefficient by multiplying it by the multiplier-table
 * entry; produce a float result.
 */

#define DEQUANTIZE(coef,quantval)  (((FAST_FLOAT) (coef)) * (quantval))


/*
 * Perform dequantization and inverse DCT on one block of coefficients.
 */

GLOBAL(void)
jpeg_idct_float (j_decompress_ptr cinfo, jpeg_component_info * compptr,
                 JCOEFPTR coef_block,
                 JSAMPARRAY output_buf, JDIMENSION output_col)
{
  FAST_FLOAT tmp0, tmp1, tmp2, tmp3, tmp4, tmp5, tmp6, tmp7;
  FAST_FLOAT tmp10, tmp11, tmp12, tmp13;
  FAST_FLOAT z5, z10, z11, z12, z13;
  JCOEFPTR inptr;
  FLOAT_MULT_TYPE * quantptr;
  FAST_FLOAT * wsptr;
  JSAMPROW outptr;
  JSAMPLE *range_limit = cinfo->sample_range_limit;
  int ctr;
  FAST_FLOAT workspace[DCTSIZE2]; /* buffers data between passes */

  /* Pass 1: process columns from input, store into work array. */

  inptr = coef_block;
  quantptr = (FLOAT_MULT_TYPE *) compptr->dct_table;
  wsptr = workspace;
  for (ctr = DCTSIZE; ctr > 0; ctr--) {
    /* Due to quantization, we will usually find that many of the input
     * coefficients are zero, especially the AC terms.  We can exploit this
     * by short-circuiting the IDCT calculation for any column in which all
     * the AC terms are zero.  In that case each output is equal to the
     * DC coefficient (with scale factor as needed).
     * With typical images and quantization tables, half or more of the
     * column DCT calculations can be simplified this way.
     */

    if (inptr[DCTSIZE*1] == 0 && inptr[DCTSIZE*2] == 0 &&
        inptr[DCTSIZE*3] == 0 && inptr[DCTSIZE*4] == 0 &&
        inptr[DCTSIZE*5] == 0 && inptr[DCTSIZE*6] == 0 &&
        inptr[DCTSIZE*7] == 0) {
      /* AC terms all zero */
      FAST_FLOAT dcval = DEQUANTIZE(inptr[DCTSIZE*0], quantptr[DCTSIZE*0]);

      wsptr[DCTSIZE*0] = dcval;
      wsptr[DCTSIZE*1] = dcval;
      wsptr[DCTSIZE*2] = dcval;
      wsptr[DCTSIZE*3] = dcval;
      wsptr[DCTSIZE*4] = dcval;
      wsptr[DCTSIZE*5] = dcval;
      wsptr[DCTSIZE*6] = dcval;
      wsptr[DCTSIZE*7] = dcval;

      inptr++;			/* advance pointers to next column */
      quantptr++;
      wsptr++;
      continue;
    }

    /* Even part */

    tmp0 = DEQUANTIZE(inptr[DCTSIZE*0], quantptr[DCTSIZE*0]);
    tmp1 = DEQUANTIZE(inptr[DCTSIZE*2], quantptr[DCTSIZE*2]);
    tmp2 = DEQUANTIZE(inptr[DCTSIZE*4], quantptr[DCTSIZE*4]);
    tmp3 = DEQUANTIZE(inptr[DCTSIZE*6], quantptr[DCTSIZE*6]);

    tmp10 = tmp0 + tmp2;	/* phase 3 */
    tmp11 = tmp0 - tmp2;

    tmp13 = tmp1 + tmp3;	/* phases 5-3 */
    tmp12 = (tmp1 - tmp3) * ((FAST_FLOAT) 1.414213562) - tmp13; /* 2*c4 */

    tmp0 = tmp10 + tmp13;	/* phase 2 */
    tmp3 = tmp10 - tmp13;
    tmp1 = tmp11 + tmp12;
    tmp2 = tmp11 - tmp12;

    /* Odd part */

    tmp4 = DEQUANTIZE(inptr[DCTSIZE*1], quantptr[DCTSIZE*1]);
    tmp5 = DEQUANTIZE(inptr[DCTSIZE*3], quantptr[DCTSIZE*3]);
    tmp6 = DEQUANTIZE(inptr[DCTSIZE*5], quantptr[DCTSIZE*5]);
    tmp7 = DEQUANTIZE(inptr[DCTSIZE*7], quantptr[DCTSIZE*7]);

    z13 = tmp6 + tmp5;		/* phase 6 */
    z10 = tmp6 - tmp5;
    z11 = tmp4 + tmp7;
    z12 = tmp4 - tmp7;

    tmp7 = z11 + z13;		/* phase 5 */
    tmp11 = (z11 - z13) * ((FAST_FLOAT) 1.414213562); /* 2*c4 */

    z5 = (z10 + z12) * ((FAST_FLOAT) 1.847759065); /* 2*c2 */
    tmp10 = z5 - z12 * ((FAST_FLOAT) 1.082392200); /* 2*(c2-c6) */
    tmp12 = z5 - z10 * ((FAST_FLOAT) 2.613125930); /* 2*(c2+c6) */

    tmp6 = tmp12 - tmp7;	/* phase 2 */
    tmp5 = tmp11 - tmp6;
    tmp4 = tmp10 - tmp5;

    wsptr[DCTSIZE*0] = tmp0 + tmp7;
    wsptr[DCTSIZE*7] = tmp0 - tmp7;
    wsptr[DCTSIZE*1] = tmp1 + tmp6;
    wsptr[DCTSIZE*6] = tmp1 - tmp6;
    wsptr[DCTSIZE*2] = tmp2 + tmp5;
    wsptr[DCTSIZE*5] = tmp2 - tmp5;
    wsptr[DCTSIZE*3] = tmp3 + tmp4;
    wsptr[DCTSIZE*4] = tmp3 - tmp4;

    inptr++;			/* advance pointers to next column */
    quantptr++;
    wsptr++;
  }

  /* Pass 2: process rows from work array, store into output array. */

  wsptr = workspace;
  for (ctr = 0; ctr < DCTSIZE; ctr++) {
    outptr = output_buf[ctr] + output_col;
    /* Rows of zeroes can be exploited in the same way as we did with columns.
     * However, the column calculation has created many nonzero AC terms, so
     * the simplification applies less often (typically 5% to 10% of the time).
     * And testing floats for zero is relatively expensive, so we don't bother.
     */

    /* Even part */

    /* Apply signed->unsigned and prepare float->int conversion */
    z5 = wsptr[0] + ((FAST_FLOAT) CENTERJSAMPLE + (FAST_FLOAT) 0.5);
    tmp10 = z5 + wsptr[4];
    tmp11 = z5 - wsptr[4];

    tmp13 = wsptr[2] + wsptr[6];
    tmp12 = (wsptr[2] - wsptr[6]) * ((FAST_FLOAT) 1.414213562) - tmp13;

    tmp0 = tmp10 + tmp13;
    tmp3 = tmp10 - tmp13;
    tmp1 = tmp11 + tmp12;
    tmp2 = tmp11 - tmp12;

    /* Odd part */

    z13 = wsptr[5] + wsptr[3];
    z10 = wsptr[5] - wsptr[3];
    z11 = wsptr[1] + wsptr[7];
    z12 = wsptr[1] - wsptr[7];

    tmp7 = z11 + z13;
    tmp11 = (z11 - z13) * ((FAST_FLOAT) 1.414213562);

    z5 = (z10 + z12) * ((FAST_FLOAT) 1.847759065); /* 2*c2 */
    tmp10 = z5 - z12 * ((FAST_FLOAT) 1.082392200); /* 2*(c2-c6) */
    tmp12 = z5 - z10 * ((FAST_FLOAT) 2.613125930); /* 2*(c2+c6) */

    tmp6 = tmp12 - tmp7;
    tmp5 = tmp11 - tmp6;
    tmp4 = tmp10 - tmp5;

    /* Final output stage: float->int conversion and range-limit */

    outptr[0] = range_limit[((int) (tmp0 + tmp7)) & RANGE_MASK];
    outptr[7] = range_limit[((int) (tmp0 - tmp7)) & RANGE_MASK];
    outptr[1] = range_limit[((int) (tmp1 + tmp6)) & RANGE_MASK];
    outptr[6] = range_limit[((int) (tmp1 - tmp6)) & RANGE_MASK];
    outptr[2] = range_limit[((int) (tmp2 + tmp5)) & RANGE_MASK];
    outptr[5] = range_limit[((int) (tmp2 - tmp5)) & RANGE_MASK];
    outptr[3] = range_limit[((int) (tmp3 + tmp4)) & RANGE_MASK];
    outptr[4] = range_limit[((int) (tmp3 - tmp4)) & RANGE_MASK];

    wsptr += DCTSIZE;		/* advance pointer to next row */
  }
}

#endif /* DCT_FLOAT_SUPPORTED */