video.rst 38.6 KB
Newer Older
wester committed
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419 420 421 422 423 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452 453 454 455 456 457 458 459 460 461 462 463 464 465 466 467 468 469 470 471 472 473 474 475 476 477 478 479 480 481 482 483 484 485 486 487 488 489 490 491 492 493 494 495 496 497 498 499 500 501 502 503 504 505 506 507 508 509 510 511 512 513 514 515 516 517 518 519 520 521 522 523 524 525 526 527 528 529 530 531 532 533 534 535 536 537 538 539 540 541 542 543 544 545 546 547 548 549 550 551 552 553 554 555 556 557 558 559 560 561 562 563 564 565 566 567 568 569 570 571 572 573 574 575 576 577 578 579 580 581 582 583 584 585 586 587 588 589 590 591 592 593 594 595 596 597 598 599 600 601 602 603 604 605 606 607 608 609 610 611 612 613 614 615 616 617 618 619 620 621 622 623 624 625 626 627 628 629 630 631 632 633 634 635 636 637 638 639 640 641 642 643 644 645 646 647 648 649 650 651 652 653 654 655 656 657 658 659 660 661 662 663 664 665 666 667 668 669 670 671 672 673 674 675 676 677 678 679 680 681 682 683 684 685 686 687 688 689 690 691 692 693 694 695 696 697 698 699 700 701 702 703 704 705 706 707 708 709 710 711 712 713 714 715 716 717 718 719 720 721 722 723 724 725 726 727 728 729 730 731 732 733 734 735 736 737 738 739 740 741 742 743 744 745 746 747 748 749 750 751 752 753 754 755 756 757 758 759 760 761 762 763 764 765 766 767 768 769 770 771 772 773 774 775 776 777 778 779 780 781 782 783 784 785 786 787 788 789 790 791 792 793 794 795 796 797 798 799 800 801 802 803 804 805 806 807 808 809 810 811 812 813 814 815 816 817 818 819 820 821 822 823 824 825 826 827 828 829 830 831 832 833 834 835 836 837 838 839 840 841 842 843 844 845 846 847 848 849 850 851 852 853 854 855 856 857 858 859 860 861 862 863 864 865 866 867 868 869 870 871 872 873 874 875 876 877 878 879 880 881 882 883 884 885 886 887 888 889 890 891 892 893 894 895 896 897 898 899 900 901 902 903 904 905 906 907 908 909 910 911 912 913 914 915 916 917 918 919 920 921 922 923 924 925 926 927 928 929 930 931 932 933 934 935 936 937 938 939 940 941 942 943 944 945 946 947 948 949 950 951 952 953 954 955 956 957 958 959 960 961 962 963 964 965 966 967 968 969 970 971 972 973 974 975 976 977 978 979 980 981 982 983 984 985 986 987 988 989 990 991 992 993 994 995 996 997 998 999 1000 1001 1002 1003 1004 1005 1006 1007 1008 1009 1010 1011 1012 1013 1014 1015 1016 1017 1018 1019 1020 1021 1022 1023 1024 1025 1026 1027 1028 1029 1030 1031 1032 1033 1034 1035 1036 1037 1038 1039 1040 1041 1042 1043 1044 1045 1046 1047 1048 1049 1050 1051 1052 1053 1054 1055 1056 1057 1058 1059 1060 1061 1062 1063 1064 1065 1066 1067 1068 1069 1070 1071 1072 1073 1074 1075 1076 1077 1078 1079 1080 1081 1082 1083 1084 1085 1086 1087 1088 1089 1090 1091 1092 1093 1094 1095 1096 1097 1098 1099 1100 1101 1102 1103 1104 1105 1106 1107 1108 1109 1110 1111 1112 1113 1114 1115 1116 1117 1118 1119 1120 1121 1122 1123 1124 1125 1126 1127 1128 1129 1130 1131 1132 1133 1134 1135 1136 1137 1138 1139 1140 1141 1142 1143 1144 1145 1146 1147 1148 1149 1150 1151 1152 1153 1154 1155
Video Analysis
==============

.. highlight:: cpp

.. note::

   * A general optical flow example can be found at opencv_source_code/samples/gpu/optical_flow.cpp
   * A general optical flow example using the Nvidia API can be found at opencv_source_code/samples/gpu/opticalflow_nvidia_api.cpp

gpu::BroxOpticalFlow
--------------------
.. ocv:class:: gpu::BroxOpticalFlow

Class computing the optical flow for two images using Brox et al Optical Flow algorithm ([Brox2004]_). ::

    class BroxOpticalFlow
    {
    public:
        BroxOpticalFlow(float alpha_, float gamma_, float scale_factor_, int inner_iterations_, int outer_iterations_, int solver_iterations_);

        //! Compute optical flow
        //! frame0 - source frame (supports only CV_32FC1 type)
        //! frame1 - frame to track (with the same size and type as frame0)
        //! u      - flow horizontal component (along x axis)
        //! v      - flow vertical component (along y axis)
        void operator ()(const GpuMat& frame0, const GpuMat& frame1, GpuMat& u, GpuMat& v, Stream& stream = Stream::Null());

        //! flow smoothness
        float alpha;

        //! gradient constancy importance
        float gamma;

        //! pyramid scale factor
        float scale_factor;

        //! number of lagged non-linearity iterations (inner loop)
        int inner_iterations;

        //! number of warping iterations (number of pyramid levels)
        int outer_iterations;

        //! number of linear system solver iterations
        int solver_iterations;

        GpuMat buf;
    };

.. note::

   * An example illustrating the Brox et al optical flow algorithm can be found at opencv_source_code/samples/gpu/brox_optical_flow.cpp

gpu::GoodFeaturesToTrackDetector_GPU
------------------------------------
.. ocv:class:: gpu::GoodFeaturesToTrackDetector_GPU

Class used for strong corners detection on an image. ::

    class GoodFeaturesToTrackDetector_GPU
    {
    public:
        explicit GoodFeaturesToTrackDetector_GPU(int maxCorners_ = 1000, double qualityLevel_ = 0.01, double minDistance_ = 0.0,
            int blockSize_ = 3, bool useHarrisDetector_ = false, double harrisK_ = 0.04);

        void operator ()(const GpuMat& image, GpuMat& corners, const GpuMat& mask = GpuMat());

        int maxCorners;
        double qualityLevel;
        double minDistance;

        int blockSize;
        bool useHarrisDetector;
        double harrisK;

        void releaseMemory();
    };

The class finds the most prominent corners in the image.

.. seealso:: :ocv:func:`goodFeaturesToTrack`



gpu::GoodFeaturesToTrackDetector_GPU::GoodFeaturesToTrackDetector_GPU
---------------------------------------------------------------------
Constructor.

.. ocv:function:: gpu::GoodFeaturesToTrackDetector_GPU::GoodFeaturesToTrackDetector_GPU(int maxCorners = 1000, double qualityLevel = 0.01, double minDistance = 0.0, int blockSize = 3, bool useHarrisDetector = false, double harrisK = 0.04)

    :param maxCorners: Maximum number of corners to return. If there are more corners than are found, the strongest of them is returned.

    :param qualityLevel: Parameter characterizing the minimal accepted quality of image corners. The parameter value is multiplied by the best corner quality measure, which is the minimal eigenvalue (see  :ocv:func:`gpu::cornerMinEigenVal` ) or the Harris function response (see  :ocv:func:`gpu::cornerHarris` ). The corners with the quality measure less than the product are rejected. For example, if the best corner has the quality measure = 1500, and the  ``qualityLevel=0.01`` , then all the corners with the quality measure less than 15 are rejected.

    :param minDistance: Minimum possible Euclidean distance between the returned corners.

    :param blockSize: Size of an average block for computing a derivative covariation matrix over each pixel neighborhood. See  :ocv:func:`cornerEigenValsAndVecs` .

    :param useHarrisDetector: Parameter indicating whether to use a Harris detector (see :ocv:func:`gpu::cornerHarris`) or :ocv:func:`gpu::cornerMinEigenVal`.

    :param harrisK: Free parameter of the Harris detector.



gpu::GoodFeaturesToTrackDetector_GPU::operator ()
-------------------------------------------------
Finds the most prominent corners in the image.

.. ocv:function:: void gpu::GoodFeaturesToTrackDetector_GPU::operator ()(const GpuMat& image, GpuMat& corners, const GpuMat& mask = GpuMat())

    :param image: Input 8-bit, single-channel image.

    :param corners: Output vector of detected corners (it will be one row matrix with CV_32FC2 type).

    :param mask: Optional region of interest. If the image is not empty (it needs to have the type  ``CV_8UC1``  and the same size as  ``image`` ), it  specifies the region in which the corners are detected.

.. seealso:: :ocv:func:`goodFeaturesToTrack`



gpu::GoodFeaturesToTrackDetector_GPU::releaseMemory
---------------------------------------------------
Releases inner buffers memory.

.. ocv:function:: void gpu::GoodFeaturesToTrackDetector_GPU::releaseMemory()



gpu::FarnebackOpticalFlow
-------------------------
.. ocv:class:: gpu::FarnebackOpticalFlow

Class computing a dense optical flow using the Gunnar Farneback’s algorithm. ::

    class CV_EXPORTS FarnebackOpticalFlow
    {
    public:
        FarnebackOpticalFlow()
        {
            numLevels = 5;
            pyrScale = 0.5;
            fastPyramids = false;
            winSize = 13;
            numIters = 10;
            polyN = 5;
            polySigma = 1.1;
            flags = 0;
        }

        int numLevels;
        double pyrScale;
        bool fastPyramids;
        int winSize;
        int numIters;
        int polyN;
        double polySigma;
        int flags;

        void operator ()(const GpuMat &frame0, const GpuMat &frame1, GpuMat &flowx, GpuMat &flowy, Stream &s = Stream::Null());

        void releaseMemory();

    private:
        /* hidden */
    };



gpu::FarnebackOpticalFlow::operator ()
--------------------------------------
Computes a dense optical flow using the Gunnar Farneback’s algorithm.

.. ocv:function:: void gpu::FarnebackOpticalFlow::operator ()(const GpuMat &frame0, const GpuMat &frame1, GpuMat &flowx, GpuMat &flowy, Stream &s = Stream::Null())

    :param frame0: First 8-bit gray-scale input image
    :param frame1: Second 8-bit gray-scale input image
    :param flowx: Flow horizontal component
    :param flowy: Flow vertical component
    :param s: Stream

.. seealso:: :ocv:func:`calcOpticalFlowFarneback`



gpu::FarnebackOpticalFlow::releaseMemory
----------------------------------------
Releases unused auxiliary memory buffers.

.. ocv:function:: void gpu::FarnebackOpticalFlow::releaseMemory()



gpu::PyrLKOpticalFlow
---------------------
.. ocv:class:: gpu::PyrLKOpticalFlow

Class used for calculating an optical flow. ::

    class PyrLKOpticalFlow
    {
    public:
        PyrLKOpticalFlow();

        void sparse(const GpuMat& prevImg, const GpuMat& nextImg, const GpuMat& prevPts, GpuMat& nextPts,
            GpuMat& status, GpuMat* err = 0);

        void dense(const GpuMat& prevImg, const GpuMat& nextImg, GpuMat& u, GpuMat& v, GpuMat* err = 0);

        Size winSize;
        int maxLevel;
        int iters;
        bool useInitialFlow;

        void releaseMemory();
    };

The class can calculate an optical flow for a sparse feature set or dense optical flow using the iterative Lucas-Kanade method with pyramids.

.. seealso:: :ocv:func:`calcOpticalFlowPyrLK`

.. note::

   * An example of the Lucas Kanade optical flow algorithm can be found at opencv_source_code/samples/gpu/pyrlk_optical_flow.cpp

gpu::PyrLKOpticalFlow::sparse
-----------------------------
Calculate an optical flow for a sparse feature set.

.. ocv:function:: void gpu::PyrLKOpticalFlow::sparse(const GpuMat& prevImg, const GpuMat& nextImg, const GpuMat& prevPts, GpuMat& nextPts, GpuMat& status, GpuMat* err = 0)

    :param prevImg: First 8-bit input image (supports both grayscale and color images).

    :param nextImg: Second input image of the same size and the same type as  ``prevImg`` .

    :param prevPts: Vector of 2D points for which the flow needs to be found. It must be one row matrix with CV_32FC2 type.

    :param nextPts: Output vector of 2D points (with single-precision floating-point coordinates) containing the calculated new positions of input features in the second image. When ``useInitialFlow`` is true, the vector must have the same size as in the input.

    :param status: Output status vector (CV_8UC1 type). Each element of the vector is set to 1 if the flow for the corresponding features has been found. Otherwise, it is set to 0.

    :param err: Output vector (CV_32FC1 type) that contains the difference between patches around the original and moved points or min eigen value if ``getMinEigenVals`` is checked. It can be NULL, if not needed.

.. seealso:: :ocv:func:`calcOpticalFlowPyrLK`



gpu::PyrLKOpticalFlow::dense
-----------------------------
Calculate dense optical flow.

.. ocv:function:: void gpu::PyrLKOpticalFlow::dense(const GpuMat& prevImg, const GpuMat& nextImg, GpuMat& u, GpuMat& v, GpuMat* err = 0)

    :param prevImg: First 8-bit grayscale input image.

    :param nextImg: Second input image of the same size and the same type as  ``prevImg`` .

    :param u: Horizontal component of the optical flow of the same size as input images, 32-bit floating-point, single-channel

    :param v: Vertical component of the optical flow of the same size as input images, 32-bit floating-point, single-channel

    :param err: Output vector (CV_32FC1 type) that contains the difference between patches around the original and moved points or min eigen value if ``getMinEigenVals`` is checked. It can be NULL, if not needed.



gpu::PyrLKOpticalFlow::releaseMemory
------------------------------------
Releases inner buffers memory.

.. ocv:function:: void gpu::PyrLKOpticalFlow::releaseMemory()



gpu::interpolateFrames
----------------------
Interpolates frames (images) using provided optical flow (displacement field).

.. ocv:function:: void gpu::interpolateFrames(const GpuMat& frame0, const GpuMat& frame1, const GpuMat& fu, const GpuMat& fv, const GpuMat& bu, const GpuMat& bv, float pos, GpuMat& newFrame, GpuMat& buf, Stream& stream = Stream::Null())

    :param frame0: First frame (32-bit floating point images, single channel).

    :param frame1: Second frame. Must have the same type and size as ``frame0`` .

    :param fu: Forward horizontal displacement.

    :param fv: Forward vertical displacement.

    :param bu: Backward horizontal displacement.

    :param bv: Backward vertical displacement.

    :param pos: New frame position.

    :param newFrame: Output image.

    :param buf: Temporary buffer, will have width x 6*height size, CV_32FC1 type and contain 6 GpuMat: occlusion masks for first frame, occlusion masks for second, interpolated forward horizontal flow, interpolated forward vertical flow, interpolated backward horizontal flow, interpolated backward vertical flow.

    :param stream: Stream for the asynchronous version.



gpu::FGDStatModel
-----------------
.. ocv:class:: gpu::FGDStatModel

  Class used for background/foreground segmentation. ::

    class FGDStatModel
    {
    public:
        struct Params
        {
            ...
        };

        explicit FGDStatModel(int out_cn = 3);
        explicit FGDStatModel(const cv::gpu::GpuMat& firstFrame, const Params& params = Params(), int out_cn = 3);

        ~FGDStatModel();

        void create(const cv::gpu::GpuMat& firstFrame, const Params& params = Params());
        void release();

        int update(const cv::gpu::GpuMat& curFrame);

        //8UC3 or 8UC4 reference background image
        cv::gpu::GpuMat background;

        //8UC1 foreground image
        cv::gpu::GpuMat foreground;

        std::vector< std::vector<cv::Point> > foreground_regions;
    };

  The class discriminates between foreground and background pixels by building and maintaining a model of the background. Any pixel which does not fit this model is then deemed to be foreground. The class implements algorithm described in [FGD2003]_.

  The results are available through the class fields:

    .. ocv:member:: cv::gpu::GpuMat background

        The output background image.

    .. ocv:member:: cv::gpu::GpuMat foreground

        The output foreground mask as an 8-bit binary image.

    .. ocv:member:: cv::gpu::GpuMat foreground_regions

        The output foreground regions calculated by :ocv:func:`findContours`.



gpu::FGDStatModel::FGDStatModel
-------------------------------
Constructors.

.. ocv:function:: gpu::FGDStatModel::FGDStatModel(int out_cn = 3)
.. ocv:function:: gpu::FGDStatModel::FGDStatModel(const cv::gpu::GpuMat& firstFrame, const Params& params = Params(), int out_cn = 3)

    :param firstFrame: First frame from video stream. Supports 3- and 4-channels input ( ``CV_8UC3`` and ``CV_8UC4`` ).

    :param params: Algorithm's parameters. See [FGD2003]_ for explanation.

    :param out_cn: Channels count in output result and inner buffers. Can be 3 or 4. 4-channels version requires more memory, but works a bit faster.

.. seealso:: :ocv:func:`gpu::FGDStatModel::create`



gpu::FGDStatModel::create
-------------------------
Initializes background model.

.. ocv:function:: void gpu::FGDStatModel::create(const cv::gpu::GpuMat& firstFrame, const Params& params = Params())

    :param firstFrame: First frame from video stream. Supports 3- and 4-channels input ( ``CV_8UC3`` and ``CV_8UC4`` ).

    :param params: Algorithm's parameters. See [FGD2003]_ for explanation.



gpu::FGDStatModel::release
--------------------------
Releases all inner buffer's memory.

.. ocv:function:: void gpu::FGDStatModel::release()



gpu::FGDStatModel::update
--------------------------
Updates the background model and returns foreground regions count.

.. ocv:function:: int gpu::FGDStatModel::update(const cv::gpu::GpuMat& curFrame)

    :param curFrame: Next video frame.



gpu::MOG_GPU
------------
.. ocv:class:: gpu::MOG_GPU

  Gaussian Mixture-based Backbround/Foreground Segmentation Algorithm. ::

    class MOG_GPU
    {
    public:
        MOG_GPU(int nmixtures = -1);

        void initialize(Size frameSize, int frameType);

        void operator()(const GpuMat& frame, GpuMat& fgmask, float learningRate = 0.0f, Stream& stream = Stream::Null());

        void getBackgroundImage(GpuMat& backgroundImage, Stream& stream = Stream::Null()) const;

        void release();

        int history;
        float varThreshold;
        float backgroundRatio;
        float noiseSigma;
    };

The class discriminates between foreground and background pixels by building and maintaining a model of the background. Any pixel which does not fit this model is then deemed to be foreground. The class implements algorithm described in [MOG2001]_.

.. seealso:: :ocv:class:`BackgroundSubtractorMOG`

.. note::

   * An example on gaussian mixture based background/foreground segmantation can be found at opencv_source_code/samples/gpu/bgfg_segm.cpp

gpu::MOG_GPU::MOG_GPU
---------------------
The constructor.

.. ocv:function:: gpu::MOG_GPU::MOG_GPU(int nmixtures = -1)

    :param nmixtures: Number of Gaussian mixtures.

Default constructor sets all parameters to default values.



gpu::MOG_GPU::operator()
------------------------
Updates the background model and returns the foreground mask.

.. ocv:function:: void gpu::MOG_GPU::operator()(const GpuMat& frame, GpuMat& fgmask, float learningRate = 0.0f, Stream& stream = Stream::Null())

    :param frame: Next video frame.

    :param fgmask: The output foreground mask as an 8-bit binary image.

    :param stream: Stream for the asynchronous version.



gpu::MOG_GPU::getBackgroundImage
--------------------------------
Computes a background image.

.. ocv:function:: void gpu::MOG_GPU::getBackgroundImage(GpuMat& backgroundImage, Stream& stream = Stream::Null()) const

    :param backgroundImage: The output background image.

    :param stream: Stream for the asynchronous version.



gpu::MOG_GPU::release
---------------------
Releases all inner buffer's memory.

.. ocv:function:: void gpu::MOG_GPU::release()



gpu::MOG2_GPU
-------------
.. ocv:class:: gpu::MOG2_GPU

  Gaussian Mixture-based Background/Foreground Segmentation Algorithm. ::

    class MOG2_GPU
    {
    public:
        MOG2_GPU(int nmixtures = -1);

        void initialize(Size frameSize, int frameType);

        void operator()(const GpuMat& frame, GpuMat& fgmask, float learningRate = 0.0f, Stream& stream = Stream::Null());

        void getBackgroundImage(GpuMat& backgroundImage, Stream& stream = Stream::Null()) const;

        void release();

        // parameters
        ...
    };

  The class discriminates between foreground and background pixels by building and maintaining a model of the background. Any pixel which does not fit this model is then deemed to be foreground. The class implements algorithm described in [MOG2004]_.

  Here are important members of the class that control the algorithm, which you can set after constructing the class instance:

    .. ocv:member:: float backgroundRatio

        Threshold defining whether the component is significant enough to be included into the background model ( corresponds to ``TB=1-cf`` from the paper??which paper??). ``cf=0.1 => TB=0.9`` is default. For ``alpha=0.001``, it means that the mode should exist for approximately 105 frames before it is considered foreground.

    .. ocv:member:: float varThreshold

        Threshold for the squared Mahalanobis distance that helps decide when a sample is close to the existing components (corresponds to ``Tg``). If it is not close to any component, a new component is generated. ``3 sigma => Tg=3*3=9`` is default. A smaller ``Tg`` value generates more components. A higher ``Tg`` value may result in a small number of components but they can grow too large.

    .. ocv:member:: float fVarInit

        Initial variance for the newly generated components. It affects the speed of adaptation. The parameter value is based on your estimate of the typical standard deviation from the images. OpenCV uses 15 as a reasonable value.

    .. ocv:member:: float fVarMin

        Parameter used to further control the variance.

    .. ocv:member:: float fVarMax

        Parameter used to further control the variance.

    .. ocv:member:: float fCT

        Complexity reduction parameter. This parameter defines the number of samples needed to accept to prove the component exists. ``CT=0.05`` is a default value for all the samples. By setting ``CT=0`` you get an algorithm very similar to the standard Stauffer&Grimson algorithm.

    .. ocv:member:: uchar nShadowDetection

        The value for marking shadow pixels in the output foreground mask. Default value is 127.

    .. ocv:member:: float fTau

        Shadow threshold. The shadow is detected if the pixel is a darker version of the background. ``Tau`` is a threshold defining how much darker the shadow can be. ``Tau= 0.5`` means that if a pixel is more than twice darker then it is not shadow. See [ShadowDetect2003]_.

    .. ocv:member:: bool bShadowDetection

        Parameter defining whether shadow detection should be enabled.

.. seealso:: :ocv:class:`BackgroundSubtractorMOG2`



gpu::MOG2_GPU::MOG2_GPU
-----------------------
The constructor.

.. ocv:function:: gpu::MOG2_GPU::MOG2_GPU(int nmixtures = -1)

    :param nmixtures: Number of Gaussian mixtures.

Default constructor sets all parameters to default values.



gpu::MOG2_GPU::operator()
-------------------------
Updates the background model and returns the foreground mask.

.. ocv:function:: void gpu::MOG2_GPU::operator()( const GpuMat& frame, GpuMat& fgmask, float learningRate=-1.0f, Stream& stream=Stream::Null() )

    :param frame: Next video frame.

    :param fgmask: The output foreground mask as an 8-bit binary image.

    :param stream: Stream for the asynchronous version.



gpu::MOG2_GPU::getBackgroundImage
---------------------------------
Computes a background image.

.. ocv:function:: void gpu::MOG2_GPU::getBackgroundImage(GpuMat& backgroundImage, Stream& stream = Stream::Null()) const

    :param backgroundImage: The output background image.

    :param stream: Stream for the asynchronous version.



gpu::MOG2_GPU::release
----------------------
Releases all inner buffer's memory.

.. ocv:function:: void gpu::MOG2_GPU::release()



gpu::GMG_GPU
------------
.. ocv:class:: gpu::GMG_GPU

  Class used for background/foreground segmentation. ::

    class GMG_GPU
    {
    public:
        GMG_GPU();

        void initialize(Size frameSize, float min = 0.0f, float max = 255.0f);

        void operator ()(const GpuMat& frame, GpuMat& fgmask, float learningRate = -1.0f, Stream& stream = Stream::Null());

        void release();

        int    maxFeatures;
        float  learningRate;
        int    numInitializationFrames;
        int    quantizationLevels;
        float  backgroundPrior;
        float  decisionThreshold;
        int    smoothingRadius;

        ...
    };

  The class discriminates between foreground and background pixels by building and maintaining a model of the background. Any pixel which does not fit this model is then deemed to be foreground. The class implements algorithm described in [GMG2012]_.

  Here are important members of the class that control the algorithm, which you can set after constructing the class instance:

    .. ocv:member:: int maxFeatures

        Total number of distinct colors to maintain in histogram.

    .. ocv:member:: float learningRate

        Set between 0.0 and 1.0, determines how quickly features are "forgotten" from histograms.

    .. ocv:member:: int numInitializationFrames

        Number of frames of video to use to initialize histograms.

    .. ocv:member:: int quantizationLevels

        Number of discrete levels in each channel to be used in histograms.

    .. ocv:member:: float backgroundPrior

        Prior probability that any given pixel is a background pixel. A sensitivity parameter.

    .. ocv:member:: float decisionThreshold

        Value above which pixel is determined to be FG.

    .. ocv:member:: float smoothingRadius

        Smoothing radius, in pixels, for cleaning up FG image.



gpu::GMG_GPU::GMG_GPU
---------------------
The default constructor.

.. ocv:function:: gpu::GMG_GPU::GMG_GPU()

Default constructor sets all parameters to default values.



gpu::GMG_GPU::initialize
------------------------
Initialize background model and allocates all inner buffers.

.. ocv:function:: void gpu::GMG_GPU::initialize(Size frameSize, float min = 0.0f, float max = 255.0f)

    :param frameSize: Input frame size.

    :param min: Minimum value taken on by pixels in image sequence. Usually 0.

    :param max: Maximum value taken on by pixels in image sequence, e.g. 1.0 or 255.



gpu::GMG_GPU::operator()
------------------------
Updates the background model and returns the foreground mask

.. ocv:function:: void gpu::GMG_GPU::operator ()( const GpuMat& frame, GpuMat& fgmask, float learningRate=-1.0f, Stream& stream=Stream::Null() )

    :param frame: Next video frame.

    :param fgmask: The output foreground mask as an 8-bit binary image.

    :param stream: Stream for the asynchronous version.



gpu::GMG_GPU::release
---------------------
Releases all inner buffer's memory.

.. ocv:function:: void gpu::GMG_GPU::release()



gpu::VideoWriter_GPU
---------------------
Video writer class.

.. ocv:class:: gpu::VideoWriter_GPU

The class uses H264 video codec.

.. note:: Currently only Windows platform is supported.

.. note::

   * An example on how to use the videoWriter class can be found at opencv_source_code/samples/gpu/video_writer.cpp

gpu::VideoWriter_GPU::VideoWriter_GPU
-------------------------------------
Constructors.

.. ocv:function:: gpu::VideoWriter_GPU::VideoWriter_GPU()
.. ocv:function:: gpu::VideoWriter_GPU::VideoWriter_GPU(const std::string& fileName, cv::Size frameSize, double fps, SurfaceFormat format = SF_BGR)
.. ocv:function:: gpu::VideoWriter_GPU::VideoWriter_GPU(const std::string& fileName, cv::Size frameSize, double fps, const EncoderParams& params, SurfaceFormat format = SF_BGR)
.. ocv:function:: gpu::VideoWriter_GPU::VideoWriter_GPU(const cv::Ptr<EncoderCallBack>& encoderCallback, cv::Size frameSize, double fps, SurfaceFormat format = SF_BGR)
.. ocv:function:: gpu::VideoWriter_GPU::VideoWriter_GPU(const cv::Ptr<EncoderCallBack>& encoderCallback, cv::Size frameSize, double fps, const EncoderParams& params, SurfaceFormat format = SF_BGR)

    :param fileName: Name of the output video file. Only AVI file format is supported.

    :param frameSize: Size of the input video frames.

    :param fps: Framerate of the created video stream.

    :param params: Encoder parameters. See :ocv:struct:`gpu::VideoWriter_GPU::EncoderParams` .

    :param format: Surface format of input frames ( ``SF_UYVY`` , ``SF_YUY2`` , ``SF_YV12`` , ``SF_NV12`` , ``SF_IYUV`` , ``SF_BGR`` or ``SF_GRAY``). BGR or gray frames will be converted to YV12 format before encoding, frames with other formats will be used as is.

    :param encoderCallback: Callbacks for video encoder. See :ocv:class:`gpu::VideoWriter_GPU::EncoderCallBack` . Use it if you want to work with raw video stream.

The constructors initialize video writer. FFMPEG is used to write videos. User can implement own multiplexing with :ocv:class:`gpu::VideoWriter_GPU::EncoderCallBack` .



gpu::VideoWriter_GPU::open
--------------------------
Initializes or reinitializes video writer.

.. ocv:function:: void gpu::VideoWriter_GPU::open(const std::string& fileName, cv::Size frameSize, double fps, SurfaceFormat format = SF_BGR)
.. ocv:function:: void gpu::VideoWriter_GPU::open(const std::string& fileName, cv::Size frameSize, double fps, const EncoderParams& params, SurfaceFormat format = SF_BGR)
.. ocv:function:: void gpu::VideoWriter_GPU::open(const cv::Ptr<EncoderCallBack>& encoderCallback, cv::Size frameSize, double fps, SurfaceFormat format = SF_BGR)
.. ocv:function:: void gpu::VideoWriter_GPU::open(const cv::Ptr<EncoderCallBack>& encoderCallback, cv::Size frameSize, double fps, const EncoderParams& params, SurfaceFormat format = SF_BGR)

The method opens video writer. Parameters are the same as in the constructor :ocv:func:`gpu::VideoWriter_GPU::VideoWriter_GPU` . The method throws :ocv:class:`Exception` if error occurs.



gpu::VideoWriter_GPU::isOpened
------------------------------
Returns true if video writer has been successfully initialized.

.. ocv:function:: bool gpu::VideoWriter_GPU::isOpened() const



gpu::VideoWriter_GPU::close
---------------------------
Releases the video writer.

.. ocv:function:: void gpu::VideoWriter_GPU::close()



gpu::VideoWriter_GPU::write
---------------------------
Writes the next video frame.

.. ocv:function:: void gpu::VideoWriter_GPU::write(const cv::gpu::GpuMat& image, bool lastFrame = false)

    :param image: The written frame.

    :param lastFrame: Indicates that it is end of stream. The parameter can be ignored.

The method write the specified image to video file. The image must have the same size and the same surface format as has been specified when opening the video writer.



gpu::VideoWriter_GPU::EncoderParams
-----------------------------------
.. ocv:struct:: gpu::VideoWriter_GPU::EncoderParams

Different parameters for CUDA video encoder. ::

    struct EncoderParams
    {
        int       P_Interval;      //    NVVE_P_INTERVAL,
        int       IDR_Period;      //    NVVE_IDR_PERIOD,
        int       DynamicGOP;      //    NVVE_DYNAMIC_GOP,
        int       RCType;          //    NVVE_RC_TYPE,
        int       AvgBitrate;      //    NVVE_AVG_BITRATE,
        int       PeakBitrate;     //    NVVE_PEAK_BITRATE,
        int       QP_Level_Intra;  //    NVVE_QP_LEVEL_INTRA,
        int       QP_Level_InterP; //    NVVE_QP_LEVEL_INTER_P,
        int       QP_Level_InterB; //    NVVE_QP_LEVEL_INTER_B,
        int       DeblockMode;     //    NVVE_DEBLOCK_MODE,
        int       ProfileLevel;    //    NVVE_PROFILE_LEVEL,
        int       ForceIntra;      //    NVVE_FORCE_INTRA,
        int       ForceIDR;        //    NVVE_FORCE_IDR,
        int       ClearStat;       //    NVVE_CLEAR_STAT,
        int       DIMode;          //    NVVE_SET_DEINTERLACE,
        int       Presets;         //    NVVE_PRESETS,
        int       DisableCabac;    //    NVVE_DISABLE_CABAC,
        int       NaluFramingType; //    NVVE_CONFIGURE_NALU_FRAMING_TYPE
        int       DisableSPSPPS;   //    NVVE_DISABLE_SPS_PPS

        EncoderParams();
        explicit EncoderParams(const std::string& configFile);

        void load(const std::string& configFile);
        void save(const std::string& configFile) const;
    };



gpu::VideoWriter_GPU::EncoderParams::EncoderParams
--------------------------------------------------
Constructors.

.. ocv:function:: gpu::VideoWriter_GPU::EncoderParams::EncoderParams()
.. ocv:function:: gpu::VideoWriter_GPU::EncoderParams::EncoderParams(const std::string& configFile)

    :param configFile: Config file name.

Creates default parameters or reads parameters from config file.



gpu::VideoWriter_GPU::EncoderParams::load
-----------------------------------------
Reads parameters from config file.

.. ocv:function:: void gpu::VideoWriter_GPU::EncoderParams::load(const std::string& configFile)

    :param configFile: Config file name.



gpu::VideoWriter_GPU::EncoderParams::save
-----------------------------------------
Saves parameters to config file.

.. ocv:function:: void gpu::VideoWriter_GPU::EncoderParams::save(const std::string& configFile) const

    :param configFile: Config file name.



gpu::VideoWriter_GPU::EncoderCallBack
-------------------------------------
.. ocv:class:: gpu::VideoWriter_GPU::EncoderCallBack

Callbacks for CUDA video encoder. ::

    class EncoderCallBack
    {
    public:
        enum PicType
        {
            IFRAME = 1,
            PFRAME = 2,
            BFRAME = 3
        };

        virtual ~EncoderCallBack() {}

        virtual unsigned char* acquireBitStream(int* bufferSize) = 0;
        virtual void releaseBitStream(unsigned char* data, int size) = 0;
        virtual void onBeginFrame(int frameNumber, PicType picType) = 0;
        virtual void onEndFrame(int frameNumber, PicType picType) = 0;
    };



gpu::VideoWriter_GPU::EncoderCallBack::acquireBitStream
-------------------------------------------------------
Callback function to signal the start of bitstream that is to be encoded.

.. ocv:function:: virtual uchar* gpu::VideoWriter_GPU::EncoderCallBack::acquireBitStream(int* bufferSize) = 0

Callback must allocate buffer for CUDA encoder and return pointer to it and it's size.



gpu::VideoWriter_GPU::EncoderCallBack::releaseBitStream
-------------------------------------------------------
Callback function to signal that the encoded bitstream is ready to be written to file.

.. ocv:function:: virtual void gpu::VideoWriter_GPU::EncoderCallBack::releaseBitStream(unsigned char* data, int size) = 0



gpu::VideoWriter_GPU::EncoderCallBack::onBeginFrame
---------------------------------------------------
Callback function to signal that the encoding operation on the frame has started.

.. ocv:function:: virtual void gpu::VideoWriter_GPU::EncoderCallBack::onBeginFrame(int frameNumber, PicType picType) = 0

    :param picType: Specify frame type (I-Frame, P-Frame or B-Frame).



gpu::VideoWriter_GPU::EncoderCallBack::onEndFrame
-------------------------------------------------
Callback function signals that the encoding operation on the frame has finished.

.. ocv:function:: virtual void gpu::VideoWriter_GPU::EncoderCallBack::onEndFrame(int frameNumber, PicType picType) = 0

    :param picType: Specify frame type (I-Frame, P-Frame or B-Frame).



gpu::VideoReader_GPU
--------------------
Class for reading video from files.

.. ocv:class:: gpu::VideoReader_GPU

.. note:: Currently only Windows and Linux platforms are supported.

.. note::

   * An example on how to use the videoReader class can be found at opencv_source_code/samples/gpu/video_reader.cpp

gpu::VideoReader_GPU::Codec
---------------------------

Video codecs supported by :ocv:class:`gpu::VideoReader_GPU` .

.. ocv:enum:: gpu::VideoReader_GPU::Codec

  .. ocv:emember:: MPEG1 = 0
  .. ocv:emember:: MPEG2
  .. ocv:emember:: MPEG4
  .. ocv:emember:: VC1
  .. ocv:emember:: H264
  .. ocv:emember:: JPEG
  .. ocv:emember:: H264_SVC
  .. ocv:emember:: H264_MVC

  .. ocv:emember:: Uncompressed_YUV420 = (('I'<<24)|('Y'<<16)|('U'<<8)|('V'))

        Y,U,V (4:2:0)

  .. ocv:emember:: Uncompressed_YV12   = (('Y'<<24)|('V'<<16)|('1'<<8)|('2'))

        Y,V,U (4:2:0)

  .. ocv:emember:: Uncompressed_NV12   = (('N'<<24)|('V'<<16)|('1'<<8)|('2'))

        Y,UV  (4:2:0)

  .. ocv:emember:: Uncompressed_YUYV   = (('Y'<<24)|('U'<<16)|('Y'<<8)|('V'))

        YUYV/YUY2 (4:2:2)

  .. ocv:emember:: Uncompressed_UYVY   = (('U'<<24)|('Y'<<16)|('V'<<8)|('Y'))

        UYVY (4:2:2)


gpu::VideoReader_GPU::ChromaFormat
----------------------------------

Chroma formats supported by :ocv:class:`gpu::VideoReader_GPU` .

.. ocv:enum:: gpu::VideoReader_GPU::ChromaFormat

  .. ocv:emember:: Monochrome = 0
  .. ocv:emember:: YUV420
  .. ocv:emember:: YUV422
  .. ocv:emember:: YUV444


gpu::VideoReader_GPU::FormatInfo
--------------------------------
.. ocv:struct:: gpu::VideoReader_GPU::FormatInfo

Struct providing information about video file format. ::

    struct FormatInfo
    {
        Codec codec;
        ChromaFormat chromaFormat;
        int width;
        int height;
    };


gpu::VideoReader_GPU::VideoReader_GPU
-------------------------------------
Constructors.

.. ocv:function:: gpu::VideoReader_GPU::VideoReader_GPU()
.. ocv:function:: gpu::VideoReader_GPU::VideoReader_GPU(const std::string& filename)
.. ocv:function:: gpu::VideoReader_GPU::VideoReader_GPU(const cv::Ptr<VideoSource>& source)

    :param filename: Name of the input video file.

    :param source: Video file parser implemented by user.

The constructors initialize video reader. FFMPEG is used to read videos. User can implement own demultiplexing with :ocv:class:`gpu::VideoReader_GPU::VideoSource` .



gpu::VideoReader_GPU::open
--------------------------
Initializes or reinitializes video reader.

.. ocv:function:: void gpu::VideoReader_GPU::open(const std::string& filename)
.. ocv:function:: void gpu::VideoReader_GPU::open(const cv::Ptr<VideoSource>& source)

The method opens video reader. Parameters are the same as in the constructor :ocv:func:`gpu::VideoReader_GPU::VideoReader_GPU` . The method throws :ocv:class:`Exception` if error occurs.



gpu::VideoReader_GPU::isOpened
------------------------------
Returns true if video reader has been successfully initialized.

.. ocv:function:: bool gpu::VideoReader_GPU::isOpened() const



gpu::VideoReader_GPU::close
---------------------------
Releases the video reader.

.. ocv:function:: void gpu::VideoReader_GPU::close()



gpu::VideoReader_GPU::read
--------------------------
Grabs, decodes and returns the next video frame.

.. ocv:function:: bool gpu::VideoReader_GPU::read(GpuMat& image)

If no frames has been grabbed (there are no more frames in video file), the methods return ``false`` . The method throws :ocv:class:`Exception` if error occurs.



gpu::VideoReader_GPU::format
----------------------------
Returns information about video file format.

.. ocv:function:: FormatInfo gpu::VideoReader_GPU::format() const

The method throws :ocv:class:`Exception` if video reader wasn't initialized.



gpu::VideoReader_GPU::dumpFormat
--------------------------------
Dump information about video file format to specified stream.

.. ocv:function:: void gpu::VideoReader_GPU::dumpFormat(std::ostream& st)

    :param st: Output stream.

The method throws :ocv:class:`Exception` if video reader wasn't initialized.



gpu::VideoReader_GPU::VideoSource
-----------------------------------
.. ocv:class:: gpu::VideoReader_GPU::VideoSource

Interface for video demultiplexing. ::

    class VideoSource
    {
    public:
        VideoSource();
        virtual ~VideoSource() {}

        virtual FormatInfo format() const = 0;
        virtual void start() = 0;
        virtual void stop() = 0;
        virtual bool isStarted() const = 0;
        virtual bool hasError() const = 0;

    protected:
        bool parseVideoData(const unsigned char* data, size_t size, bool endOfStream = false);
    };

User can implement own demultiplexing by implementing this interface.



gpu::VideoReader_GPU::VideoSource::format
-----------------------------------------
Returns information about video file format.

.. ocv:function:: virtual FormatInfo gpu::VideoReader_GPU::VideoSource::format() const = 0



gpu::VideoReader_GPU::VideoSource::start
----------------------------------------
Starts processing.

.. ocv:function:: virtual void gpu::VideoReader_GPU::VideoSource::start() = 0

Implementation must create own thread with video processing and call periodic :ocv:func:`gpu::VideoReader_GPU::VideoSource::parseVideoData` .



gpu::VideoReader_GPU::VideoSource::stop
---------------------------------------
Stops processing.

.. ocv:function:: virtual void gpu::VideoReader_GPU::VideoSource::stop() = 0



gpu::VideoReader_GPU::VideoSource::isStarted
--------------------------------------------
Returns ``true`` if processing was successfully started.

.. ocv:function:: virtual bool gpu::VideoReader_GPU::VideoSource::isStarted() const = 0



gpu::VideoReader_GPU::VideoSource::hasError
-------------------------------------------
Returns ``true`` if error occured during processing.

.. ocv:function:: virtual bool gpu::VideoReader_GPU::VideoSource::hasError() const = 0



gpu::VideoReader_GPU::VideoSource::parseVideoData
-------------------------------------------------
Parse next video frame. Implementation must call this method after new frame was grabbed.

.. ocv:function:: bool gpu::VideoReader_GPU::VideoSource::parseVideoData(const uchar* data, size_t size, bool endOfStream = false)

    :param data: Pointer to frame data. Can be ``NULL`` if ``endOfStream`` if ``true`` .

    :param size: Size in bytes of current frame.

    :param endOfStream: Indicates that it is end of stream.



.. [Brox2004] T. Brox, A. Bruhn, N. Papenberg, J. Weickert. *High accuracy optical flow estimation based on a theory for warping*. ECCV 2004.
.. [FGD2003] Liyuan Li, Weimin Huang, Irene Y.H. Gu, and Qi Tian. *Foreground Object Detection from Videos Containing Complex Background*. ACM MM2003 9p, 2003.
.. [MOG2001] P. KadewTraKuPong and R. Bowden. *An improved adaptive background mixture model for real-time tracking with shadow detection*. Proc. 2nd European Workshop on Advanced Video-Based Surveillance Systems, 2001
.. [MOG2004] Z. Zivkovic. *Improved adaptive Gausian mixture model for background subtraction*. International Conference Pattern Recognition, UK, August, 2004
.. [ShadowDetect2003] Prati, Mikic, Trivedi and Cucchiarra. *Detecting Moving Shadows...*. IEEE PAMI, 2003
.. [GMG2012] A. Godbehere, A. Matsukawa and K. Goldberg. *Visual Tracking of Human Visitors under Variable-Lighting Conditions for a Responsive Audio Art Installation*. American Control Conference, Montreal, June 2012